ns am relocating to one all electric apartment and also have a gas dryer. It is 3 years old. Can it be convert to an electrical dryer? how would I find someone to perform this?


In general, no you can"t perform this.

You are watching: Can you convert a gas dryer to electric

I expect it"s feasible that the manufacturer uses plenty of of the very same parts in between their gas and electric models and also you could buy enough parts to carry out a conversion, however this would most likely cost more than simply buying an electric dryer in the very first place.

But I"ve never seen a supported conversion kit - mine advice: sell the gas dryer and buy one electric.


You might transform it to use propane. That method you can keep using it. There space some videos around how to perform it.

Don"t know around how that will impact its working, or longevity.





I expect you could, but it doesn"t do sense. Gas is nearly always cheaper than power per kilowatt. So the operational price is less for the gas dryer. In addition gas produces much more BTU than electric so the gas dryer is much more efficient and also will dry the clothes faster. The only down side is the initial expense of the appliance is a bit higher for a gas dryer

Yes, a mechanical control gas dryer can be converted to an electrical dryer, just as a mechanical regulate electric dryer deserve to be converted to gas. The newer computer controlled appliances may be problematic for conversions, i.e., also expensive to do it a feasible option, (but who knows, possibly flip a dip switch on the board and also it can work just fine). Otherwise, ~ above a mechanical manage dryer, many of the components are the exact same whether gas or electric(or propane i m sorry is a relatively simple, safe and also inexpensive conversion indigenous NG).

While ns am acquainted with Alliance products, ns am fairly certain many dryers would be the same. As far as dryers go, manufacturers save time and also money by having most choices built into the cabinets and also controls, in various other words, most of the cabinet and moving components of dryers room the exact same whether gas or electric, and also have been unchanged for decades. What has changed, and not constantly for the better, are the controls and their consoles/panels. Mechanically controls seldom if ever malfunction in a residential setting, whereas computer controls have the right to go poor for a variety of reasons and also are expensive come replace.

The very first thing would be to eliminate the parts specific to the gas dryer:the gas lead-in pipeline assembly, shut off valve and also elbow, igniter and also bracket assembly, burner assembly, the coils and also gas valve assembly and mounting bracket, warmth duct shroud, burning duct and also limit thermostat, and the 110 power lead in cord.Then we would replace every one of the above with an electrical heater kit (either 208 or 240 volts) which consists of all cable assemblies, thermal fuse assembly, and also limit thermostat, the mounting feet are already in the heater duct the attaches to.Next comes the 220 terminal block and terminal block shield which affix to the backside that the rear bulkhead assembly, the mounting holes are already there on every dryers as space the 220 terminal block accessibility cutout and cover ~ above the rear of the cabinet, with which is mounted the 3 prong or 4 prong 220 command in cord.

And ultimately the wiring, the security cabinet exploit assembly and wire harness assembly certain to the device (front or behind controls) have to be adjusted to the versions suitable to the machine"s serial number and the brand-new electric heater.

For any type of looking in ~ a gas to electric conversion, it would be wise to inspect/replace items such as the (2) cylinder rollers, and the (2) cylinder roller shafts, the cylinder belt, the idler lever and also wheel assembly, and also the versatile exhaust venting outside of the an equipment which may become clogged v lint.Since many of the working parts must be eliminated from within the dryer because that this conversion, it is quite easily accessible to usage of a vacuum to remove all lint inside the room or the vents in ~ the rear, and also all that holds the motor and also exhaust fan assembly is 2 screws and also a strength clip, so the doesn"t take long to eliminate it and blow out any lint i beg your pardon has collected inside the blower housing and on the motor.

See more: Does Harry Styles Have A Daughter, Girlfriend, Album, Harry Styles

The kick panel on many dryers has actually 2 5/16 screws holding the on, and also if you have actually someone who can remove it friend can examine to view if over there is a buildup of lint inside, if so friend should contact for service, or if therefore inclined, unplug the an equipment and very closely vacuum out everything lint is obtainable because a buildup that lint within the dryer is a fire danger whether gas or electric.